can't get time to sync

Support section for FREESCO v0.4.x

can't get time to sync

Postby Kalist Shawxo » Mon Nov 30, 2009 12:05 pm

I set the time In the BIOS prior to boot... boot up, and it's wrong and when I try to sync time, I get the error:

Code: Select all
30 Nov 12:02:56 ntpdate[4944]: no server suitable for synchronization found
ntpdate path = /bin/ntpdate
work file = /tmp/freetime.dat
www.clock.org, +0000
server 192.5.16.65, stratum 0, offset 0.000000, delay 0.00000
time zone = EST
Time correction = 0 seconds
Succesfully adjusted clock



I have the Eastern time zone file in the TMZ directory.

So I did a DATE command to set the time then did a CLOCK -w to write it to the system. after that I still get the same error trying to sync from the control panel. regardless of the timeserver used. Odd thing is, it DID work before... so I am sure it is just something that got screwed up while we were fixing the slow boot and poor response time issues.

Here's the system report:
Code: Select all
   FREESCO v System Report.
   Generated - Mon Nov 30 12:03:37  2009
System language: english


----- clock -----
Mon Nov 30 12:03:38 2009


----- cat /etc/system.cfg -----
# [System]
ROUTER=ethernet   # dialup/leased/ethernet/bridge
HOSTNAME=APU   #Router name
DOMAIN=Springfield   #Local domain
ENAMSQ=s     #NAT/firewall
STLTH=s      #Stealth or Reject=
NPNG=s      #ICMP responses
NBRG=n       #Bridging mode
BIGMEM=y    #Command line history
RMDRV=n      #Ram disk
RSRM=n      #Manual ramdisk control
RMSZ=2      #Ramdisk size in MB
SVRS=30,0     #Blank screen,hdd. 0 = off
SSVR="15,tclock,24,ra"   #Screen saver,Name,options. 0 = off
SWPSZ=0      #Swap size. 0 = off
LGSZ=50000,5000,50000   #System,Logins,Info log sizes
SVLG=n      #Save system logs
NBP=y      #Beeps
NBPT=1600,2200   #start, stop
NBPF=y      #Firewall sound
NBPD=y      #DHCP server
NBPDH=y      #DHCP client
NBPL=y      #Login sound
NBPP=y      #New IP sound
NBPPD=y      #PPP down sound
NBPPO=y      #Power off
NMN=n      #Flashing leds
NLGGR=y      #Network monitor
NTOP=y      #Top monitor
NCON=n      #ISP connect time
DCON=n      #RAS connect time
LLED=n      #Link LED
CLRS=y      #Console colors
NPNP=n      #ISA PnP
DFSP=      #Default dialup ISP
RDNLY=n      #Run in ram
EDIT=/bin/edt   #Default editor
NMLCK=y      #NUM lock
# [Log/Debug]
LGDHCP=y   #DHCP server
DHCPLG=y   #DHCP client
LGDNS=y      #DNS
LOGHTTP=y   #HTTP/control
LGCHT=n      #Chat
LGDLD=n      #Diald
LGDLP=n      #Dialup
LGNT=0      #Netmeeting [0-4]
LGPPPD=s   #pppd
LGDNT=s      #Ident
LGFTP=s      #FTP
LGLP=s       #Printer
LGFR=s      #firewall
# [Services/servers]
NDNS=s          #DNS Server
DNSCCH=600      #Cache. 0 = disable
NCRN=n         #Cron daemon
NDHCP=n       #DHCP server
WINSADDR=      #WINS address
LZTM=64000,128000   #lease-time,max-lease-time
ENAWWW=s       #HTTP Server
WWWPORT=1080      #port
USRWWW=n      #User web pages
RESWWW=n      #Bandwidth
RESVAL=25000      #Bps
ENAWWA=s       #Control via HTTP
WWAPORT=1082       #port
CPW=25         #left width %
CPH=15         #bottom height %
TIMADDR=www.clock.org   #NTP URL, empty = disable
TIMZONE=+0000      #Offset to UTC
ENALPD=n       #Print Server
LPPORT0=515      #port
NSSHD=n         #SSH/SFTP server
SSHP=22         #port
SSHCMD=""   #Extra command line options
NPFWD=n         #Port forwarding
ENADYNDNS=n      #Dynamic name client
NDNP=y         #Dyndns local URL
NID=s         #Ident server
NFTP=s         #FTP Server
FTPPRT=21      #port
FTPCN=1      #FTP connections
FTPCC=10         #Concurrent FTP connections
FTPNN=n         #Anonymous FTP
RTFTP=y         #allow root
FTPBW=""      #FTP Bandwidth
NRS=n         #Dialin
SRS=n         #Silent modem
ENASMTP=y      #Email client
SVRMN=""      #Server monitor
SVRTM=2         #check time
PKGDOMAIN=http://www.freescosoft.com/0.4.x/  #package URL
STST=14666
HOMEURL=http://www.freesco.org/   #Patch URL
PKGDR=/www/packages/0.4.x   #Package save dir
# [Security]
TRSTN0=y       #Trust net0
TRSTN1=y       #Trust net1
TRSTMD=n      #Trust dial IN
RNGS=1,10      #Rings login,nologin time
MonTM=""      #Nologin times
TueTM=""
WedTM=""
ThuTM=""
FriTM=""
SatTM=""
SunTM=""
MDI=n      #Load icq
MDD=n      #Load raudio
MDV=n      #Load vdolive
MDQ=n      #Load quake
MDR=n      #Load irc
MDF=y      #Load ftp
MDN=n      #Load netmeeting
XTRAPTS="0:1056,1720,5000"   #Stealthed ports
# [Hardware COM Ports]
# [Modems]
# [ diald ]
# [ethernet/leased/printer/ras router]
GATEWAY=24.210.97.1      #Gateway
DNSDDR=209.18.47.61      #Primary DNS
DNSDDR1=209.18.47.62      #Second
DNSDDR2=      #Third
DNSDDR3=      #Fourth
PROXY=""      #HTTP proxy addr[:port]
   
# [Ethernet hardware]
IO0=0x300
IRQ0=10
IO1=0x210
IRQ1=11
   
# [Network 0]
SDHCP=y            #DHCP client
DHCPDNS=y         #DNS via DHCP
INTNAME0=eth0         #Interface
IPADDR0=24.210.97.231      #IP address
NETMASK0=255.255.255.0      #Netmask
NETWORK0=24.210.97.0      #Network address
BRDCAST0=255.255.255.255      #Broadcast address
IPRANGE0=""   #DHCP server IP range
# [Network 1]
INTNAME1=eth1         #Interface
IPADDR1=10.0.0.1      #IP address
NETMASK1=255.255.255.0      #Netmask
NETWORK1=10.0.0.0      #Network address
BRDCAST1=10.0.0.255      #Broadcast address
IPRANGE1=""   #DHCP server IP range


----- cat /etc/live.cfg -----
DNSDDR=209.18.47.61
DNSDDR1=209.18.47.62


----- cat /etc/dhcpc/dhcpcd-eth0.info -----
IPADDR=24.210.97.231
NETMASK=255.255.255.0
NETWORK=24.210.97.0
BROADCAST=255.255.255.255
GATEWAY=24.210.97.1
HOSTNAME='APU'
DOMAIN='twmi.rr.com'
DNS=209.18.47.61,209.18.47.62
DHCPSID=10.57.0.1
DHCPGIADDR=10.57.0.1
DHCPSIADDR=0.0.0.0
DHCPCHADDR=00:50:04:04:A8:A3
DHCPSHADDR=00:19:2F:E5:DF:05
DHCPSNAME=''
LEASETIME=86400
RENEWALTIME=43200
REBINDTIME=75600
INTERFACE='eth0'
CLASSID='Linux 2.0.40 i486'
CLIENTID=00:50:04:04:A8:A3


----- cat /etc/portfw.cfg | sed s/\#.*//g -----
 


----- cat /etc/restrict.cfg | sed s/\#.*//g -----


----- sed -n 1,/\#@@/P /etc/chat.pwd -----
ISPNAME=


----- lsmod -----
Module      Pages      Used by
ip_masq_ftp        1      0
3c509.e-n          2      2


----- ls -l /boot/drv/ -----
-rw-r--r--    1 root     root         4556 Feb  7  2009 3c509.gz


----- dmesg | sed -n /eth/P -----
eth0: 3c509 at 0x300 tag 1, 10baseT port, address  00 50 04 04 a8 a3, IRQ 10.
eth1: 3c509 at 0x210 tag 2, 10baseT port, address  00 60 08 9d 9a b5, IRQ 11.
eth0: Setting Rx mode to 1 addresses.
eth1: Setting Rx mode to 0 addresses.
eth1: Setting Rx mode to 1 addresses.
eth0: Setting Rx mode to 0 addresses.
eth1: Setting Rx mode to 1 addresses.
eth0: Setting Rx mode to 0 addresses.
eth1: Setting Rx mode to 1 addresses.


----- ifconfig -----
eth0      Link encap:Ethernet  HWaddr 00:50:04:04:A8:A3 
          inet addr:24.210.97.231  Bcast:255.255.255.255  Mask:255.255.255.0
          UP BROADCAST NOTRAILERS RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:125201 errors:0 dropped:0 overruns:0 frame:0
          TX packets:4365 errors:0 dropped:0 overruns:0 carrier:0
          collisions:16           Interrupt:10 Base address:0x300
eth1      Link encap:Ethernet  HWaddr 00:60:08:9D:9A:B5 
          inet addr:10.0.0.1  Bcast:10.0.0.255  Mask:255.255.255.0
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:7859 errors:0 dropped:0 overruns:0 frame:0
          TX packets:7213 errors:0 dropped:0 overruns:0 carrier:0
          collisions:41           Interrupt:11 Base address:0x210
lo        Link encap:Local Loopback 
          inet addr:127.0.0.1  Bcast:127.255.255.255  Mask:255.0.0.0
          UP BROADCAST LOOPBACK RUNNING  MTU:3584  Metric:1
          RX packets:44 errors:0 dropped:0 overruns:0 frame:0
          TX packets:44 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0


----- cat /proc/interrupts -----
 0:     354531   timer
 1:          4   keyboard
 2:          0   cascade
 8:          7 + rtc
10:     124829   3c509
11:       8573   3c509
13:          1   math error
14:       4117 + ide0


----- cat /proc/ioports -----
0000-001f : dma1
0020-003f : pic1
0040-005f : timer
0060-006f : keyboard
0070-007f : rtc
0080-009f : dma page reg
00a0-00bf : pic2
00c0-00df : dma2
00f0-00ff : npu
01f0-01f7 : ide0
0210-021f : 3c509
0300-030f : 3c509
03bc-03be : lp
03c0-03df : vga+
03f0-03f5 : floppy
03f6-03f6 : ide0
03f7-03f7 : floppy DIR


----- route -n -----
Kernel IP routing table
Destination     Gateway         Genmask         Flags Metric Ref    Use Iface
255.255.255.255 0.0.0.0         255.255.255.255 UH    0      0        0 eth1
10.0.0.0        0.0.0.0         255.255.255.0   U     0      0        4 eth1
24.210.97.0     0.0.0.0         255.255.255.0   U     0      0        3 eth0
127.0.0.0       0.0.0.0         255.0.0.0       U     0      0        4 lo
0.0.0.0         24.210.97.1     0.0.0.0         UG    0      0       35 eth0


----- cat /etc/dhcpd.leases | sed s/#.*//g -----


----- uptime -----
 12:03pm  up 59 min, load average: 0.65, 0.48, 0.49


----- free -----
        total:    used:    free:  shared: buffers:  cached:
Mem:  64778240 12275712 52502528  7565312  4984832  2875392
Swap:        0        0        0
MemTotal:     63260 kB
MemFree:      51272 kB
MemShared:     7388 kB
Buffers:       4868 kB
Cached:        2808 kB
SwapTotal:        0 kB
SwapFree:         0 kB
Mounted FS:
/dev/root / ext2 rw 0 0
/proc /proc proc rw 0 0
/dev/hda1 /mnt/bootdev ext2 rw 0 0
Filesystem           1k-blocks      Used Available Use% Mounted on
/dev/ram0                 3963      2265      1698  57% /
/dev/hda1               232179     41615    178574  19% /mnt/bootdev


----- ps -----
  Pid   Stat   Parent   Line   Name   Command
  1    S   0      init   init
  2    S   1      kflushd   
  3    S   1      kswapd   
  289    S   1      syslogd   syslogd-r-h-m0
  291    S   1      klogd   klogd-c3
  1377    S   1      update   update
  1465    S   1      dhcpcd   dhcpcd-d-R-t50-c/sbin/dhcpcd.update-hAPUeth0
  2885    S   1      oidentd   oidentd-m-F-unobody-gnobody-xAPU
  2958    S   1      pure-ftpd   pure-ftpd (SERVER)
  3069    S   1      thttpd_c   thttpd_c-d/wwa-p1082-uroot
  3190    S   1      tsaver   tsaver900nice-n19tclock24
  3208    S   1      logrotate   logrotatehda150000500050000
  3211    S   1      daemon   sh/sbin/daemon-agetty -n -l /bin/netmon 38400 tty6
  3214    S   1      daemon   sh/sbin/daemon-agetty -n -l /sbin/top 38400 tty7
  3220    S   1      agetty   /sbin/agetty38400/dev/tty1
  3221    S   1      agetty   /sbin/agetty38400tty2
  3235    S   3211      netmon   /bin/netmon--
  3236    S   3214      top   /sbin/top--
  3545    S   3190      tclock   sh/bin/tclock24
  19419    S   1      dnsmasq   dnsmasq-RnbfDeq-Q65330-S209.18.47.61-S209.18.47.62-sSpringfield-c600
  22907    S   3069      usr.cgi   shusr.cgiinfo
  22908    S   22907      thttpd_c   thttpd_c-d/wwa-p1082-uroot
  22919    S   22907      sysinfo   sh/bin/sysinfo
  22920    S   22907      usr.cgi   shusr.cgiinfo
  22922    S   22920      sed   seds/\&/\&/;s/</\</;s/>/\>/
  23037    S   22919      sysinfo   sh/bin/sysinfo
  23038    S   22919      sed   sed/^$/d
  23039    R   23037      ps   sh/bin/ps


----- cat /etc/ppp/opt* -----
asyncmap 0


----- setserial -bg /dev/cua? -----


----- ls -C /pkg/db/install/ -----
dutch                     italian                   perl_5.6.1_dingetje
english                   openssl-0.9.6g-lightning  swedish
ext2-0.4.2-lewis          patches-042-1


----- cat /etc/isapnp.cfg |sed 's/#.*//g' -----


----- hardinfo -----
   
processor   : 0
model      : Am5x86-WT
vendor_id   : AuthenticAMD
bogomips   : 66.56
   
MemTotal:     63260 kB
   
   
/dev/lp0 at 0x03bc
   
Kalist Shawxo
Junior Member
 
Posts: 25
Joined: Sun Nov 22, 2009 3:17 am

Re: can't get time to sync

Postby Lightning » Tue Dec 01, 2009 9:12 pm

If this did work originally and now with the BIOS changes it no longer does, then most likely this is a BIOS setting issue because the system has to be able to write to the BIOS to set the correct time which is always in GMT when using a time zone file.
However before pursuing this much further I would wait and see what the new kernel does on your system and it may solve this issue on it's own.
If you are afraid that you might make a mistake. The chances are high that you will never learn anything.
User avatar
Lightning
FREESCO GOD !!
 
Posts: 12080
Joined: Wed Nov 14, 2001 6:50 am
Location: Oregon, USA

Re: can't get time to sync

Postby Kalist Shawxo » Wed Dec 02, 2009 3:23 am

sounds like a plan... I'll get the existing kernel problem fixed, get back online to download the updated kernel, see if it makes any changes, then if not check and recheck the BIOS. I am glad it is my "friday"... my next two days are gonna be busy!
Kalist Shawxo
Junior Member
 
Posts: 25
Joined: Sun Nov 22, 2009 3:17 am


Return to FREESCO Support for v0.4.x

Who is online

Users browsing this forum: No registered users and 8 guests

cron