EXT2 is really slow?

Support section for FREESCO v0.4.x

EXT2 is really slow?

Postby Kalist Shawxo » Thu Nov 26, 2009 7:26 am

ok, I went ahead and did the EXT2 install to my existing HDD... I followed the instructions and split the hard drive into two partitions, 118MB and 127MB.

When I did the transfer over from floppy to HDD all of the configuration settings were blank. So after going through all the settings and recreating everything, it takes 10 minutes for the system to get up and running.

I did add a couple more services, but even when in the setup, I hit a key and it takes almost a count of "10" before the system responds.

is this typical?

also, when I login to the control panel on port 82.... it doesn't completely load everything in the left pane. it shows "services" and under it only shows "Firewall" and nothing else... not even the switches for the firewall... just the word itself.

The only hardware change I made was I doubled the ram from 32 to 64MB.... do I need the swap file? do I need the RAM drive? should I just reinstall it clean onto one partition with no swap file?

I put in a system report below.. can't figure out why I am getting so many of the :
"IP fw-in deny eth0 UDP 10.57.0.1:67 255.255.255.255:68 L=400 S=0x00 I=15688 F=0x0000 T=255"

Code: Select all
   FREESCO v0.4.2 System Report.
   Generated - Thu Nov 26 06:43:40 EST 2009
System language: english


----- clock -----
Thu Nov 26 06:43:51 2009


----- cat /etc/system.cfg -----
# [System]
ROUTER=ethernet   # dialup/leased/ethernet/bridge
HOSTNAME=apu   #Router name
DOMAIN=springfield   #Local domain
ENAMSQ=s     #NAT/firewall
STLTH=s      #Stealth or Reject=
NPNG=s      #ICMP responses
NBRG=n       #Bridging mode
BIGMEM=n    #Command line history
RMDRV=y      #Ram disk
RSRM=n      #Manual ramdisk control
RMSZ=      #Ramdisk size in MB
SVRS=30,0     #Blank screen,hdd. 0 = off
SSVR="10,tclock,24,ra"   #Screen saver,Name,options. 0 = off
SWPSZ=/dev/hda2      #Swap size. 0 = off
LGSZ=d,5000,50000   #System,Logins,Info log sizes
SVLG=n      #Save system logs
NBP=y      #Beeps
NBPT=1600,2200   #start, stop
NBPF=y      #Firewall sound
NBPD=y      #DHCP server
NBPDH=y      #DHCP client
NBPL=y      #Login sound
NBPP=y      #New IP sound
NBPPD=y      #PPP down sound
NBPPO=y      #Power off
NMN=n      #Flashing leds
NLGGR=y      #Network monitor
NTOP=y      #Top monitor
NCON=      #ISP connect time
DCON=n      #RAS connect time
LLED=n      #Link LED
CLRS=      #Console colors
NPNP=y      #ISA PnP
DFSP=      #Default dialup ISP
RDNLY=n      #Run in ram
EDIT=   #Default editor
NMLCK=y      #NUM lock
# [Log/Debug]
LGDHCP=n   #DHCP server
DHCPLG=n   #DHCP client
LGDNS=y      #DNS
LOGHTTP=y   #HTTP/control
LGCHT=n      #Chat
LGDLD=n      #Diald
LGDLP=n      #Dialup
LGNT=0      #Netmeeting [0-4]
LGPPPD=n   #pppd
LGDNT=s      #Ident
LGFTP=e      #FTP
LGLP=n       #Printer
LGFR=e      #firewall
# [Services/servers]
NDNS=s          #DNS Server
DNSCCH=500      #Cache. 0 = disable
NCRN=y         #Cron daemon
NDHCP=n       #DHCP server
WINSADDR=      #WINS address
LZTM=   #lease-time,max-lease-time
ENAWWW=s       #HTTP Server
WWWPORT=1080      #port
USRWWW=n      #User web pages
RESWWW=n      #Bandwidth
RESVAL=      #Bps
ENAWWA=s       #Control via HTTP
WWAPORT=82       #port
CPW=20         #left width %
CPH=15         #bottom height %
TIMADDR=www.clock.org   #NTP URL, empty = disable
TIMZONE=+0000      #Offset to UTC
ENALPD=n       #Print Server
LPPORT0=515      #port
NSSHD=n         #SSH/SFTP server
SSHP=22         #port
SSHCMD=""   #Extra command line options
NPFWD=n         #Port forwarding
ENADYNDNS=n      #Dynamic name client
NDNP=         #Dyndns local URL
NID=s         #Ident server
NFTP=s         #FTP Server
FTPPRT=21      #port
FTPCN=1      #FTP connections
FTPCC=10         #Concurrent FTP connections
FTPNN=n         #Anonymous FTP
RTFTP=y         #allow root
FTPBW=""      #FTP Bandwidth
NRS=n         #Dialin
SRS=         #Silent modem
ENASMTP=y      #Email client
SVRMN=",dns,http,control,ident,ftp"      #Server monitor
SVRTM=60         #check time
PKGDOMAIN=  #package URL
STST=14664
HOMEURL=   #Patch URL
PKGDR=   #Package save dir
# [Security]
TRSTN0=y       #Trust net0
TRSTN1=y       #Trust net1
TRSTMD=n      #Trust dial IN
RNGS=1,10      #Rings login,nologin time
MonTM=""      #Nologin times
TueTM=""
WedTM=""
ThuTM=""
FriTM=""
SatTM=""
SunTM=""
MDI=n      #Load icq
MDD=n      #Load raudio
MDV=n      #Load vdolive
MDQ=n      #Load quake
MDR=n      #Load irc
MDF=n      #Load ftp
MDN=n      #Load netmeeting
XTRAPTS="1:1024"   #Stealthed ports
# [Hardware COM Ports]
# [Modems]
# [ diald ]
# [ethernet/leased/printer/ras router]
GATEWAY=75.184.96.1      #Gateway
DNSDDR=209.18.47.61      #Primary DNS
DNSDDR1=209.18.47.62      #Second
DNSDDR2=      #Third
DNSDDR3=      #Fourth
PROXY=""      #HTTP proxy addr[:port]
   
# [Ethernet hardware]
IO0=0x300
IRQ0=10
IO1=0x210
IRQ1=11
   
# [Network 0]
SDHCP=y            #DHCP client
DHCPDNS=y         #DNS via DHCP
INTNAME0=eth0         #Interface
IPADDR0=75.184.96.145      #IP address
NETMASK0=255.255.252.0      #Netmask
NETWORK0=75.184.96.0      #Network address
BRDCAST0=255.255.255.255      #Broadcast address
IPRANGE0=""   #DHCP server IP range
# [Network 1]
INTNAME1=eth1         #Interface
IPADDR1=10.0.0.1      #IP address
NETMASK1=255.255.255.0      #Netmask
NETWORK1=10.0.0.0      #Network address
BRDCAST1=10.0.0.255      #Broadcast address
IPRANGE1=""   #DHCP server IP range


----- cat /etc/live.cfg -----
BOOTMOD=
VERSION=0.4.2
BOOTDEV=hda1
BOOTIME="Sat Nov 26 05:54:23  1994"
IPADDR0=75.184.96.145
NETMASK0=255.255.252.0
BRDCAST0=255.255.255.255
NETWORK0=75.184.96.0
GATEWAY=75.184.96.1
IPADDR0=75.184.96.145
NETMASK0=255.255.252.0
BRDCAST0=255.255.255.255
NETWORK0=75.184.96.0
GATEWAY=75.184.96.1
DNSDDR=209.18.47.61
DNSDDR=209.18.47.61
DNSDDR1=209.18.47.62
DNSDDR1=209.18.47.62


----- cat /etc/dhcpc/dhcpcd-eth0.info -----
IPADDR=75.184.96.145
NETMASK=255.255.252.0
NETWORK=75.184.96.0
BROADCAST=255.255.255.255
GATEWAY=75.184.96.1
HOSTNAME='apu'
DOMAIN='twmi.rr.com'
DNS=209.18.47.61,209.18.47.62
DHCPSID=10.57.0.1
DHCPGIADDR=10.57.0.1
DHCPSIADDR=0.0.0.0
DHCPCHADDR=00:50:04:04:A8:A3
DHCPSHADDR=00:19:2F:E5:DF:05
DHCPSNAME=''
LEASETIME=86400
RENEWALTIME=43200
REBINDTIME=75600
INTERFACE='eth0'
CLASSID='Linux 2.0.40 i486'
CLIENTID=00:50:04:04:A8:A3


----- cat /etc/portfw.cfg | sed s/\#.*//g -----
 


----- cat /etc/restrict.cfg | sed s/\#.*//g -----


----- sed -n 1,/\#@@/P /etc/chat.pwd -----
ISPNAME=


----- lsmod -----
Module      Pages      Used by
3c509.e-n          2      2


----- ls -l /boot/drv/ -----
-rw-r--r--    1 root     root         4556 Feb  6  2009 3c509.gz


----- dmesg | sed -n /eth/P -----
IP fw-in deny eth0 UDP 10.57.0.1:67 255.255.255.255:68 L=400 S=0x00 I=15688 F=0x0000 T=255
IP fw-in deny eth0 UDP 10.57.0.1:67 255.255.255.255:68 L=352 S=0x00 I=15829 F=0x0000 T=255
IP fw-in deny eth0 TCP 64.118.88.20:33225 75.184.96.145:113 L=60 S=0x00 I=48550 F=0x4000 T=53
IP fw-in deny eth0 UDP 10.57.0.1:67 255.255.255.255:68 L=356 S=0x00 I=15865 F=0x0000 T=255
IP fw-in deny eth0 UDP 10.57.0.1:67 255.255.255.255:68 L=336 S=0x00 I=15909 F=0x0000 T=255
IP fw-in deny eth0 TCP 64.118.88.20:54567 75.184.96.145:113 L=60 S=0x00 I=46162 F=0x4000 T=53
IP fw-in deny eth0 UDP 10.57.0.1:67 255.255.255.255:68 L=338 S=0x00 I=16002 F=0x0000 T=255
IP fw-in deny eth0 UDP 10.57.0.1:67 255.255.255.255:68 L=356 S=0x00 I=16199 F=0x0000 T=255
IP fw-in deny eth0 UDP 10.57.0.1:67 255.255.255.255:68 L=352 S=0x00 I=16237 F=0x0000 T=255
IP fw-in deny eth0 UDP 10.57.0.1:67 255.255.255.255:68 L=352 S=0x00 I=16286 F=0x0000 T=255
IP fw-in deny eth0 TCP 64.118.88.20:44761 75.184.96.145:113 L=60 S=0x00 I=29455 F=0x4000 T=53
IP fw-in deny eth0 UDP 10.57.0.1:67 255.255.255.255:68 L=400 S=0x00 I=16397 F=0x0000 T=255
IP fw-in deny eth0 UDP 10.57.0.1:67 255.255.255.255:68 L=400 S=0x00 I=16456 F=0x0000 T=255
IP fw-in deny eth0 UDP 10.57.0.1:67 255.255.255.255:68 L=350 S=0x00 I=16481 F=0x0000 T=255
IP fw-in deny eth0 TCP 64.118.88.20:58128 75.184.96.145:113 L=60 S=0x00 I=28747 F=0x4000 T=53
IP fw-in deny eth0 UDP 10.57.0.1:67 255.255.255.255:68 L=352 S=0x00 I=16532 F=0x0000 T=255
IP fw-in deny eth0 UDP 10.57.0.1:67 255.255.255.255:68 L=356 S=0x00 I=16564 F=0x0000 T=255
IP fw-in deny eth0 UDP 10.57.0.1:67 255.255.255.255:68 L=358 S=0x00 I=16723 F=0x0000 T=255
IP fw-in deny eth0 TCP 64.118.88.20:42899 75.184.96.145:113 L=60 S=0x00 I=868 F=0x4000 T=53
IP fw-in deny eth0 TCP 64.118.88.20:39096 75.184.96.145:113 L=60 S=0x00 I=30613 F=0x4000 T=53
IP fw-in deny eth0 UDP 10.57.0.1:67 255.255.255.255:68 L=336 S=0x00 I=17004 F=0x0000 T=255
IP fw-in deny eth0 UDP 10.57.0.1:67 255.255.255.255:68 L=336 S=0x00 I=17041 F=0x0000 T=255
IP fw-in deny eth0 UDP 10.57.0.1:67 255.255.255.255:68 L=348 S=0x00 I=17076 F=0x0000 T=255
IP fw-in deny eth0 UDP 10.57.0.1:67 255.255.255.255:68 L=336 S=0x00 I=17125 F=0x0000 T=255
IP fw-in deny eth0 UDP 10.57.0.1:67 255.255.255.255:68 L=336 S=0x00 I=17184 F=0x0000 T=255
IP fw-in deny eth0 UDP 10.57.0.1:67 255.255.255.255:68 L=336 S=0x00 I=17288 F=0x0000 T=255
IP fw-in deny eth0 TCP 64.118.88.20:43866 75.184.96.145:113 L=60 S=0x00 I=61672 F=0x4000 T=53
IP fw-in deny eth0 TCP 64.118.88.20:58224 75.184.96.145:113 L=60 S=0x00 I=38461 F=0x4000 T=53
IP fw-in deny eth0 UDP 10.57.0.1:67 255.255.255.255:68 L=336 S=0x00 I=17480 F=0x0000 T=255
IP fw-in deny eth0 UDP 10.57.0.1:67 255.255.255.255:68 L=400 S=0x00 I=17571 F=0x0000 T=255
IP fw-in deny eth0 UDP 10.57.0.1:67 255.255.255.255:68 L=400 S=0x00 I=17592 F=0x0000 T=255
IP fw-in deny eth0 UDP 10.57.0.1:67 255.255.255.255:68 L=352 S=0x00 I=17768 F=0x0000 T=255
IP fw-in deny eth0 UDP 10.57.0.1:67 255.255.255.255:68 L=356 S=0x00 I=17793 F=0x0000 T=255
IP fw-in deny eth0 UDP 10.57.0.1:67 255.255.255.255:68 L=336 S=0x00 I=17828 F=0x0000 T=255
IP fw-in deny eth0 UDP 10.57.0.1:67 255.255.255.255:68 L=336 S=0x00 I=17842 F=0x0000 T=255
IP fw-in deny eth0 TCP 64.118.88.20:44480 75.184.96.145:113 L=60 S=0x00 I=39005 F=0x4000 T=53
IP fw-in deny eth0 UDP 10.57.0.1:67 255.255.255.255:68 L=338 S=0x00 I=17941 F=0x0000 T=255
IP fw-in deny eth0 UDP 10.57.0.1:67 255.255.255.255:68 L=352 S=0x00 I=17954 F=0x0000 T=255
IP fw-in deny eth0 TCP 64.118.88.20:58127 75.184.96.145:113 L=60 S=0x00 I=50000 F=0x4000 T=53
IP fw-in deny eth0 UDP 10.57.0.1:67 255.255.255.255:68 L=354 S=0x00 I=18092 F=0x0000 T=255
IP fw-in deny eth0 UDP 10.57.0.1:67 255.255.255.255:68 L=352 S=0x00 I=18177 F=0x0000 T=255
IP fw-in deny eth0 UDP 10.57.0.1:67 255.255.255.255:68 L=354 S=0x00 I=18238 F=0x0000 T=255
IP fw-in deny eth0 TCP 64.118.88.20:48351 75.184.96.145:113 L=60 S=0x00 I=64921 F=0x4000 T=53
IP fw-in deny eth0 TCP 64.118.88.20:42298 75.184.96.145:113 L=60 S=0x00 I=23297 F=0x4000 T=53
IP fw-in deny eth0 UDP 10.57.0.1:67 255.255.255.255:68 L=336 S=0x00 I=18574 F=0x0000 T=255
IP fw-in deny eth0 UDP 10.57.0.1:67 255.255.255.255:68 L=336 S=0x00 I=18617 F=0x0000 T=255
IP fw-in deny eth0 UDP 10.57.0.1:67 255.255.255.255:68 L=354 S=0x00 I=18642 F=0x0000 T=255
IP fw-in deny eth0 UDP 10.57.0.1:67 255.255.255.255:68 L=336 S=0x00 I=18701 F=0x0000 T=255
IP fw-in deny eth0 UDP 10.57.0.1:67 255.255.255.255:68 L=336 S=0x00 I=18800 F=0x0000 T=255
IP fw-in deny eth0 UDP 10.57.0.1:67 255.255.255.255:68 L=356 S=0x00 I=18859 F=0x0000 T=255
IP fw-in deny eth0 UDP 10.57.0.1:67 255.255.255.255:68 L=350 S=0x00 I=18889 F=0x0000 T=255
IP fw-in deny eth0 UDP 10.57.0.1:67 255.255.255.255:68 L=352 S=0x00 I=18918 F=0x0000 T=255
IP fw-in deny eth0 UDP 10.57.0.1:67 255.255.255.255:68 L=400 S=0x00 I=18963 F=0x0000 T=255
IP fw-in deny eth0 UDP 10.57.0.1:67 255.255.255.255:68 L=336 S=0x00 I=18998 F=0x0000 T=255
IP fw-in deny eth0 UDP 10.57.0.1:67 255.255.255.255:68 L=400 S=0x00 I=19027 F=0x0000 T=255
IP fw-in deny eth0 UDP 10.57.0.1:67 255.255.255.255:68 L=350 S=0x00 I=19064 F=0x0000 T=255
IP fw-in deny eth0 TCP 64.118.88.20:57828 75.184.96.145:113 L=60 S=0x00 I=33016 F=0x4000 T=53
IP fw-in deny eth0 TCP 64.118.88.20:47890 75.184.96.145:113 L=60 S=0x00 I=21169 F=0x4000 T=53
IP fw-in deny eth0 UDP 10.57.0.1:67 255.255.255.255:68 L=336 S=0x00 I=19221 F=0x0000 T=255
IP fw-in deny eth0 UDP 10.57.0.1:67 255.255.255.255:68 L=352 S=0x00 I=19330 F=0x0000 T=255
IP fw-in deny eth0 TCP 64.118.88.20:53691 75.184.96.145:113 L=60 S=0x00 I=32640 F=0x4000 T=53
IP fw-in deny eth0 TCP 64.118.88.20:53740 75.184.96.145:113 L=60 S=0x00 I=16745 F=0x4000 T=53
IP fw-in deny eth0 UDP 10.57.0.1:67 255.255.255.255:68 L=354 S=0x00 I=19603 F=0x0000 T=255
IP fw-in deny eth0 UDP 10.57.0.1:67 255.255.255.255:68 L=352 S=0x00 I=19729 F=0x0000 T=255
IP fw-in deny eth0 TCP 64.118.88.20:44422 75.184.96.145:113 L=60 S=0x00 I=47145 F=0x4000 T=53
IP fw-in deny eth0 TCP 64.118.88.20:35788 75.184.96.145:113 L=60 S=0x00 I=18150 F=0x4000 T=53
IP fw-in deny eth0 UDP 10.57.0.1:67 255.255.255.255:68 L=350 S=0x00 I=20087 F=0x0000 T=255
IP fw-in deny eth0 UDP 10.57.0.1:67 255.255.255.255:68 L=336 S=0x00 I=20116 F=0x0000 T=255
IP fw-in deny eth0 UDP 10.57.0.1:67 255.255.255.255:68 L=336 S=0x00 I=20145 F=0x0000 T=255
IP fw-in deny eth0 UDP 10.57.0.1:67 255.255.255.255:68 L=336 S=0x00 I=20188 F=0x0000 T=255
IP fw-in deny eth0 UDP 10.57.0.1:67 255.255.255.255:68 L=336 S=0x00 I=20263 F=0x0000 T=255
IP fw-in deny eth0 UDP 10.57.0.1:67 255.255.255.255:68 L=352 S=0x00 I=20282 F=0x0000 T=255
IP fw-in deny eth0 UDP 10.57.0.1:67 255.255.255.255:68 L=354 S=0x00 I=20307 F=0x0000 T=255
IP fw-in deny eth0 UDP 10.57.0.1:67 255.255.255.255:68 L=336 S=0x00 I=20349 F=0x0000 T=255
IP fw-in deny eth0 UDP 10.57.0.1:67 255.255.255.255:68 L=336 S=0x00 I=20380 F=0x0000 T=255
IP fw-in deny eth0 UDP 10.57.0.1:67 255.255.255.255:68 L=336 S=0x00 I=20420 F=0x0000 T=255
IP fw-in deny eth0 UDP 10.57.0.1:67 255.255.255.255:68 L=336 S=0x00 I=20452 F=0x0000 T=255
IP fw-in deny eth0 UDP 10.57.0.1:67 255.255.255.255:68 L=348 S=0x00 I=20491 F=0x0000 T=255
IP fw-in deny eth0 UDP 10.57.0.1:67 255.255.255.255:68 L=350 S=0x00 I=20540 F=0x0000 T=255
IP fw-in deny eth0 UDP 10.57.0.1:67 255.255.255.255:68 L=336 S=0x00 I=20594 F=0x0000 T=255
IP fw-in deny eth0 UDP 10.57.0.1:67 255.255.255.255:68 L=336 S=0x00 I=20650 F=0x0000 T=255
IP fw-in deny eth0 UDP 10.57.0.1:67 255.255.255.255:68 L=336 S=0x00 I=20677 F=0x0000 T=255
IP fw-in deny eth0 UDP 10.57.0.1:67 255.255.255.255:68 L=336 S=0x00 I=20748 F=0x0000 T=255
IP fw-in deny eth0 TCP 64.118.88.20:48350 75.184.96.145:113 L=60 S=0x00 I=21215 F=0x4000 T=53
IP fw-in deny eth0 UDP 10.57.0.1:67 255.255.255.255:68 L=350 S=0x00 I=20795 F=0x0000 T=255
IP fw-in deny eth0 TCP 64.118.88.20:54953 75.184.96.145:113 L=60 S=0x00 I=9366 F=0x4000 T=53


----- ifconfig -----
eth0      Link encap:Ethernet  HWaddr 00:50:04:04:A8:A3 
          inet addr:75.184.96.145  Bcast:255.255.255.255  Mask:255.255.252.0
          UP BROADCAST NOTRAILERS RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:103444 errors:0 dropped:0 overruns:0 frame:0
          TX packets:3127 errors:0 dropped:0 overruns:0 carrier:0
          collisions:1           Interrupt:10 Base address:0x300
eth1      Link encap:Ethernet  HWaddr 00:60:08:9D:9A:B5 
          inet addr:10.0.0.1  Bcast:10.0.0.255  Mask:255.255.255.0
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:5576 errors:0 dropped:0 overruns:0 frame:0
          TX packets:3621 errors:0 dropped:0 overruns:0 carrier:0
          collisions:2           Interrupt:11 Base address:0x210
lo        Link encap:Local Loopback 
          inet addr:127.0.0.1  Bcast:127.255.255.255  Mask:255.0.0.0
          UP BROADCAST LOOPBACK RUNNING  MTU:3584  Metric:1
          RX packets:262 errors:0 dropped:0 overruns:0 frame:0
          TX packets:262 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0


----- cat /proc/interrupts -----
 0:     312811   timer
 1:        128   keyboard
 2:          0   cascade
 8:          3 + rtc
10:     103194   3c509
11:       5620   3c509
13:          1   math error
14:        769 + ide0


----- cat /proc/ioports -----
0000-001f : dma1
0020-003f : pic1
0040-005f : timer
0060-006f : keyboard
0070-007f : rtc
0080-009f : dma page reg
00a0-00bf : pic2
00c0-00df : dma2
00f0-00ff : npu
01f0-01f7 : ide0
0210-021f : 3c509
0300-030f : 3c509
03bc-03be : lp
03c0-03df : vga+
03f0-03f5 : floppy
03f6-03f6 : ide0
03f7-03f7 : floppy DIR


----- route -n -----
Kernel IP routing table
Destination     Gateway         Genmask         Flags Metric Ref    Use Iface
255.255.255.255 0.0.0.0         255.255.255.255 UH    0      0        0 eth1
10.0.0.0        0.0.0.0         255.255.255.0   U     0      0        6 eth1
75.184.96.0     0.0.0.0         255.255.252.0   U     0      0        2 eth0
127.0.0.0       0.0.0.0         255.0.0.0       U     0      0        5 lo
0.0.0.0         75.184.96.1     0.0.0.0         UG    0      0       14 eth0


----- cat /etc/dhcpd.leases | sed s/#.*//g -----


----- uptime -----
  6:45am  up 52 min, load average: 8.60, 8.56, 8.51


----- free -----
        total:    used:    free:  shared: buffers:  cached:
Mem:  64778240 32194560 32583680  8318976 21827584  1548288
Swap: 127479808        0 127479808
MemTotal:     63260 kB
MemFree:      31820 kB
MemShared:     8124 kB
Buffers:      21316 kB
Cached:        1512 kB
SwapTotal:   124492 kB
SwapFree:    124492 kB
Mounted FS:
/dev/root / ext2 rw 0 0
/proc /proc proc rw 0 0
/dev/hda1 /mnt/bootdev ext2 rw 0 0
/dev/ram1 /mnt/ram1 ext2 rw 0 0
Filesystem           1k-blocks      Used Available Use% Mounted on
/dev/ram0                 3963      2172      1791  55% /
/dev/hda1               111628      2097    103766   2% /mnt/bootdev
/dev/ram1                15863         3     15041   0% /mnt/ram1


----- ps -----
  Pid   Stat   Parent   Line   Name   Command
  1    S   0      init   init
  2    S   1      kflushd   
  3    S   1      kswapd   
  289    S   1      syslogd   syslogd-r-h-m0
  510    S   1      klogd   klogd-c3
  1698    S   1      update   update
  1783    S   1      dhcpcd   dhcpcd-R-t50-c/sbin/dhcpcd.update-hapueth0
  2381    S   1      crond   crond-b-c/etc/cron
  2526    S   1      oidentd   oidentd-m-F-unobody-gnobody-xapu
  2723    S   1      pure-ftpd   pure-ftpd (SERVER)
  2908    R   1      thttpd   thttpd-d/www-p1080-unobody
  3016    R   1      thttpd_c   thttpd_c-d/wwa-p82-uroot
  3262    S   1      tsaver   tsaver600nice-n19tclock24
  3313    S   1      logrotate   logrotatehda1d500050000
  3321    S   1      daemon   sh/sbin/daemon-agetty -n -l /bin/netmon 38400 tty6
  3326    S   1      daemon   sh/sbin/daemon-agetty -n -l /sbin/top 38400 tty7
  3331    S   1      servermon   sh/sbin/servermon
  3356    S   1      agetty   /sbin/agetty38400tty2
  3379    S   3321      netmon   /bin/netmon--
  3639    S   3331      sleep   sleep3600
  8329    S   1      agetty   /sbin/agetty38400/dev/tty1
  8780    S   1      dnsmasq   dnsmasq-RnbfDeq-Q65331-S209.18.47.61-S209.18.47.62-sspringfield-c500
  8795    S   1      dnsmasq   dnsmasq-RnbfDeq-Q65414-S209.18.47.61-S209.18.47.62-sspringfield-c500
  9989    S   1      thttpd_c   thttpd_c-d/wwa-p82-uroot
  10061    S   1      sysinfo   sh/bin/sysinfo
  10062    S   1      usr.cgi   shusr.cgiinfo
  10064    S   10062      sed   seds/\&/\&/;s/</\</;s/>/\>/
  10622    S   10061      sysinfo   sh/bin/sysinfo
  10623    S   10061      sed   sed/^$/d
  10624    R   10622      ps   sh/bin/ps


----- cat /etc/ppp/opt* -----
asyncmap 0


----- setserial -bg /dev/cua? -----


----- ls -C /pkg/db/install/ -----
ext2-0.4.2-lewis


----- cat /etc/isapnp.cfg |sed 's/#.*//g' -----


----- hardinfo -----
   
processor   : 0
model      : Am5x86-WT
vendor_id   : AuthenticAMD
bogomips   : 66.56
   
MemTotal:     63260 kB
   
   
/dev/lp0 at 0x03bc
Kalist Shawxo
Junior Member
 
Posts: 25
Joined: Sun Nov 22, 2009 3:17 am

Re: EXT2 is really slow?

Postby Lightning » Thu Nov 26, 2009 2:26 pm

I hit a key and it takes almost a count of "10" before the system responds.

is this typical?

Absolutely not.

As for your current configuration there are several things that should be changed.

First reinstall and do NOT create any swap file. The reason is because swap can really slow the system down and if you have at least 16MB of ram there really is no need for it.

Second Enable the big mem option (on by default) so that you have command line history at the console.

Third disable the extra ram disk because that option is really only needed for floppy installs when you want to install packages and it uses valuable memory that can be used by the system.

Fourth to start with I would not enable the server monitor. That option is only needed if you end up having some server stability issues and it also uses some extra resources.

Most likely though if you disable swap it might speed the system up. However usually the reason a system runs as slow as you are describing is because there is an error running in the background consuming all of the CPU cycles. Which if you check screen 7 (ALT+F7) you will see what process is causing the issue. Although in some cases an error in the hard drive system can do the same thing . So be sure to format the drive using error checking.
If you are afraid that you might make a mistake. The chances are high that you will never learn anything.
User avatar
Lightning
FREESCO GOD !!
 
Posts: 12080
Joined: Wed Nov 14, 2001 6:50 am
Location: Oregon, USA

Re: EXT2 is really slow?

Postby Kalist Shawxo » Fri Nov 27, 2009 10:52 pm

I had already done a clean install..but I of course duplicated my same settings..so it is still slow. I will then this weekend:

start by disabling the swap.... if that shows improvement, then I will reformat and reinstall cleanly, making sure to:

Remove the swap partition entirely and NOT use a swap file, remove the RAM drive, make sure bigmem is enabled, and disable the server monitors and report back,

I did look into the ALT-F7 screen and there were repeated errors about /proc/ not found...
Kalist Shawxo
Junior Member
 
Posts: 25
Joined: Sun Nov 22, 2009 3:17 am

Re: EXT2 is really slow?

Postby Kalist Shawxo » Sat Nov 28, 2009 8:58 am

I think 0.4.2 just doesn't like me. :(

I turned off the swap, the RAM drive, disabled the server monitors and turned on BIGMEM.. no effect.

so, I have created new install floppies. and I am going to do a complete start over from scratch. run the install to floppy, configure basic workings, transfer to EXT2 hard drive and put in the remaining settings... and see how she goes. Currently it literally takes 10 mins to load up, response in setup is up to 10 secs to a keystroke. 0.2.7 was a minute to load up (on a FAT drive) and super responsive. I am out of ideas.
Kalist Shawxo
Junior Member
 
Posts: 25
Joined: Sun Nov 22, 2009 3:17 am

Re: EXT2 is really slow? no, it is 0.4.2

Postby Kalist Shawxo » Sat Nov 28, 2009 11:14 am

Ok... fresh floppy of 0.4.2.

Ran setup with minimum required settings to run router, reboot and the time to load up the router was.

at 0:00 start timing at end of BIOS, start of Floppy access
at 2:05 "mounting drive" came up
at 6:03 "modules" done loading
at 6:33 "DHCP address" done
at 10:03 Login prompt comes up.

as soon as that was done, I logged in as root, ran the EXT2 package install, and then rebooted:

at 0:00 started timing at end of BIOS, start of HDD access
at 1:03 "mounting drive" came up
at 5:05 "modules" done loading
at 5:35 ""DHCP address" done
at 9:05 Login prompt comes up.

So it doesn't appear to be a EXT2 issue, it just seems that 0.4.2 is really struggling on here.

0.2.7 took way less time to load up.

Oh, and just for the heck of it.. I timed a shut down as well. I logged in as root, issued the REBOOT command and started the timing when "shutting down" came on the screen.

total time to system shut down was 7:05.

Logging in, typing ROOT and then the password, still has a delay of 10 seconds or so before it changes screen to a regular prompt.

Making changes to anything in the setup takes a long time, and just to reboot takes about 17 minutes from REBOOT to LOGIN when you include BIOS and memory count.

Suggestions??
Kalist Shawxo
Junior Member
 
Posts: 25
Joined: Sun Nov 22, 2009 3:17 am

Re: EXT2 is really slow?

Postby Lightning » Sat Nov 28, 2009 2:22 pm

If even the initial startup floppy takes that long to boot then there is something seriously wrong with the kernel and your system. What is the make and model of your computer ?
It is probable that a kernel change to eliminate the recursive error would solve this problem. You can check the "dmesg" after startup to see if there is something shown in the startup logs. Because this problem has to be reasonably early in the system.

Run this command

dmesg | more


On a secondary note this problem could be caused from a poor math co-processor on your system because 0.2.7 came by default with a software math co-processor enabled. Which can be duplicated in the 04x series by loading the "kernel.sx" from the freesc0-042.zip file and replacing the "kernel" on the floppy.
If you are afraid that you might make a mistake. The chances are high that you will never learn anything.
User avatar
Lightning
FREESCO GOD !!
 
Posts: 12080
Joined: Wed Nov 14, 2001 6:50 am
Location: Oregon, USA

Re: EXT2 is really slow?

Postby Kalist Shawxo » Sat Nov 28, 2009 2:44 pm

Hello again Lightning!

the system is running on a 486DX-133 (Evergreen Processor Upgrade Chip), I will run the dmesg when I get up later, I had attempted to run the package install check and it has been checking servers for the last two hours... so I am off to bed.

I will replace the kernel on the newest 4.2 floppy I made, with the kernel.sx and boot to it... see what the effect is before modifying the hard drive copy. I will have to re run lilo after swapping the kernel on the EXT2 HDD right?

I had hoped once all the upgrading is done, to install apache.. is that still gonna be possible?

Thanks again for all your help.
Kalist Shawxo
Junior Member
 
Posts: 25
Joined: Sun Nov 22, 2009 3:17 am

Re: EXT2 is really slow?

Postby Lightning » Sat Nov 28, 2009 2:55 pm

I will have to re run lilo after swapping the kernel on the EXT2 HDD right?

Yes, although the system is designed to auto detect kernel and ramdisk changes and run lilo automatically at shutdown time.
I had hoped once all the upgrading is done, to install apache.. is that still gonna be possible?
If the system will run at a reasonable speed yes it is possible. At present the system will not be capable of doing anything.
Also you should know that I recommend a Pentium class CPU for 037, 038, and the 04x series. But a 486 running at 133Mhz should be fast enough. At this point knowing what your processor is I am pretty sure that the kernel change will resolve most of the problems with speed.
If you are afraid that you might make a mistake. The chances are high that you will never learn anything.
User avatar
Lightning
FREESCO GOD !!
 
Posts: 12080
Joined: Wed Nov 14, 2001 6:50 am
Location: Oregon, USA

Re: EXT2 is really slow?

Postby Peppe/Sweden » Sat Nov 28, 2009 6:07 pm

486DX-133
I doubled the ram from 32 to 64MB


I have 486 DX 33 mhz with 32 mb memory at my parents house running 0.4.2 .
A boot takes about two minutes and i use a Compact flash ide adapter as a harddrive .

So a 486DX 133 mhz witth either 32 mb or 64 mb would be fine , regardless.
I would check bios so that plug and play is off and that memory cache is on and check all other options .
The simplest way would be to reset bios setting and the test to boot .
If no performence change is noticed , I would try to disable/change settings in bios until any change is noticed .

Good luck ! :D

Regards , Peter
[COLOR=blue] You mean that I don?t fly airplanes , I don?t have a grilfriend and don?t have a dog ? Buuh , I grow up to be a real loser! (The Kid , walt disney) [COLOR=blue]
User avatar
Peppe/Sweden
Junior Advanced Member
 
Posts: 161
Joined: Wed Feb 05, 2003 4:41 pm

Re: EXT2 is really slow?

Postby Kalist Shawxo » Sun Nov 29, 2009 11:14 am

Sorry for the lateness of this reply... I woke up sick yesterday and barely went to work... so I just got to it this morning.

So, I copied the kernel.sx to the floppy. (renaming it kernel) and I didn't have my watch handy when I booted, but it did load in less time, and the walking penguin moved visibly faster.

so I mounted the hd, and copied the kernel from the fd over the kernel on the hd.

reboot to the hd, and it took 10:12 to get to the login prompt. so I figure I did something wrong, or it was cause the lilo wasn't run.

so I mount the fd, and copied the kernel from the fd over the kernel in the /mnt/bootdev/ folder. then ran lilo, and rebooted.

starting the timer again at the point the BIOS is done and the hd is first accessed:
1:00 til it displays "mounting boot device"
3:30 til it displays "loading modules"
5:13 til modules are "done"
5:39 til DHCP address is gotten
11:55 til the login prompt is displayed.

so it is now SLOWER to load with the sx kernel, assuming I did it right... which I am not assuming at all.

the DMESG | more I forgot to run before copying over the kernel, but the sx kernel reports the following:
Code: Select all
Memory: sized by int13 088h
Console: 16 point font, 400 scans
Console: colour VGA+ 80x25, 1 virtual console (max 63)
pci_init: no BIOS32 detected
Calibrating delay loop.. ok - 66.56 BogoMIPS
Memory: 62252k/65536k available (652k kernel code, 384k reserved, 1240k data, 0k badram)
This processor honours the WP bit even when in supervisor mode. Good.
Swansea University Computer Society NET3.035 for Linux 2.0
NET3: Unix domain sockets 0.13 for Linux NET3.035.
Swansea University Computer Society TCP/IP for NET3.034
IP Protocols: IGMP, ICMP, UDP, TCP
Linux IP multicast router 0.07.
Checking 386/387 coupling... fpu using exception 16.
Checking 'hlt'... Ok.
Linux version 2.0.40 (Lewis@Official-FREESCO-kernel) (gcc version 2.7.2.3) #94 Thu Aug 28 19:12:18 PDT 2008
Starting kswapd v 1.4.2.2
Serial driver version 4.13p1 with no serial options enabled
lp0 at 0x03bc, (polling)
Real Time Clock Driver v1.09
Ramdisk driver initialized : 16 ramdisks of 16384K size
loop: registered device at major 7
hda: Maxtor 7245 AT, 234MB w/64kB Cache, CHS=967/16/31
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
Ethernet Bridge 002 for NET3.035 (Linux 2.0)
PPP: version 2.3.11 (demand dialing)
TCP compression code copyright 1989 Regents of the University of California
PPP line discipline registered.
SLIP: version 0.8.4-NET3.019-NEWTTY (dynamic channels, max=256).
CSLIP: code copyright 1989 Regents of the University of California.
Partition check:
 hda: hda1
RAMDISK: Compressed image found at block 0
VFS: Mounted root (ext2 filesystem).
pci-scan.c:v1.12 7/30/2003  Donald Becker <becker@scyld.com> http://www.scyld.com/linux/drivers.html
eth0: 3c509 at 0x300 tag 1, 10baseT port, address  00 50 04 04 a8 a3, IRQ 10.
3c509.c:1.16 2/3/98 becker@cesdis.gsfc.nasa.gov
eth1: 3c509 at 0x210 tag 2, 10baseT port, address  00 60 08 9d 9a b5, IRQ 11.
3c509.c:1.16 2/3/98 becker@cesdis.gsfc.nasa.gov
3c59x.c:v0.99Zc 12/15/2003 Donald Becker, becker@scyld.com
  http://www.scyld.com/network/vortex.html
eepro100.c:v1.28a 12/05/2003 Donald Becker <becker@scyld.com>
  http://www.scyld.com/network/eepro100.html
eepro100: No cards found, driver not installed.
rtl8139.c:v1.24 11/13/2003 Donald Becker, becker@scyld.com.
 http://www.scyld.com/network/rtl8139.html
via-rhine.c:v1.16 7/22/2003  Written by Donald Becker <becker@scyld.com>
  http://www.scyld.com/network/via-rhine.html
eth0: Setting Rx mode to 1 addresses.
eth1: Setting Rx mode to 0 addresses.
eth1: Setting Rx mode to 1 addresses.


is there a different kernel I should try? won't I need a diff one for running apache anyway if we get this figured out? or did I brainfart the installation of the replacement kernel?
Kalist Shawxo
Junior Member
 
Posts: 25
Joined: Sun Nov 22, 2009 3:17 am

Re: EXT2 is really slow?

Postby Lightning » Sun Nov 29, 2009 2:12 pm

You have an unusual CPU in this system and there must be some sort of quirk causing this issue. There have been a number of code changes that might effect things like this but probably the most likely difference is the extra ramdisk sizes and a couple of kernel flags in the startup that can be changed.
So for a test edit the syslinux.cfg file on a floppy

Find and remove in each startup line "ramdisk_size=16384" and add "no387 no-hlt" in it's place.

Also be sure to run the kernel.sx on this floppy. Then boot the changed floppy in "setup" mode so that FREESCO doesn't try and load a large ramdisk at startup time.

If that solves the problem the bootup speed will immediately improve and if you want you casn go back through the changes and just make one of the above three changes to find out exactly which single one was causing the problem. If you don't use the "no387" flag then the stock kernel can be used because that is what disables the math-coprocessor. If the ramdisk_size" option is left then you can run the ramdisk. Once you know exactly which command solves the problem the change can be made to the hard drive install in the /etc/lilo.cfg and /boot/etc/lilo.cfg files.
If you are afraid that you might make a mistake. The chances are high that you will never learn anything.
User avatar
Lightning
FREESCO GOD !!
 
Posts: 12080
Joined: Wed Nov 14, 2001 6:50 am
Location: Oregon, USA

Re: EXT2 is really slow?

Postby Kalist Shawxo » Sun Nov 29, 2009 10:11 pm

ok... so I changed the floppy... now it doesn't boot... gives errors reading disk and asks for another disk.

so, in lieu of creating yet another floppy and starting over... FTP'd into it the HDD version and made changes to the two lilo.conf files, replacing the "ramdisk_size=16384" with "no387 no-hlt". reboot and.... total time to boot to login prompt was.... 9:45. mild improvement...but I think still a bit long.

the startup still show loading ramdisk... so I am not sure what the changes to the lilo files did or did not do.

Contents of lilo.conf on hd:
Code: Select all
boot = /dev/hda
initrd = /boot/ramdisk
root = /dev/ram0
timeout = 80
default = normal
message = /boot/boot.message
prompt

image = /boot/kernel
 append = "no387 no-hlt BOOTDEV=hda1 DLANG=english panic=20 EXT2FS=y"
 label = normal
 read-write

image = /boot/kernel
 append = "no387 no-hlt BOOTMOD=setup DLANG=english BOOTDEV=hda1 panic=20 EXT2FS=y"
 label = setup
 read-write

image = /boot/kernel
 append = "no387 no-hlt BOOTMOD=debug DLANG=english BOOTDEV=hda1 panic=20 EXT2FS=y"
 label = debug
 read-write

image = /boot/kernel
 append = "no387 no-hlt BOOTMOD=shell DLANG=english BOOTDEV=hda1 panic=20 EXT2FS=y"
 label = shell
 read-write

other = /dev/fd0
 label = floppy
 unsafe


latest DMESG report:

Code: Select all
Memory: sized by int13 088h
Console: 16 point font, 400 scans
Console: colour VGA+ 80x25, 1 virtual console (max 63)
pci_init: no BIOS32 detected
Calibrating delay loop.. ok - 66.56 BogoMIPS
Memory: 62252k/65536k available (652k kernel code, 384k reserved, 1240k data, 0k badram)
This processor honours the WP bit even when in supervisor mode. Good.
Swansea University Computer Society NET3.035 for Linux 2.0
NET3: Unix domain sockets 0.13 for Linux NET3.035.
Swansea University Computer Society TCP/IP for NET3.034
IP Protocols: IGMP, ICMP, UDP, TCP
Linux IP multicast router 0.07.
Checking 386/387 coupling... fpu using exception 16.
Checking 'hlt'... Ok.
Linux version 2.0.40 (Lewis@Official-FREESCO-kernel) (gcc version 2.7.2.3) #94 Thu Aug 28 19:12:18 PDT 2008
Starting kswapd v 1.4.2.2
Serial driver version 4.13p1 with no serial options enabled
lp0 at 0x03bc, (polling)
Real Time Clock Driver v1.09
Ramdisk driver initialized : 16 ramdisks of 16384K size
loop: registered device at major 7
hda: Maxtor 7245 AT, 234MB w/64kB Cache, CHS=967/16/31
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
Ethernet Bridge 002 for NET3.035 (Linux 2.0)
PPP: version 2.3.11 (demand dialing)
TCP compression code copyright 1989 Regents of the University of California
PPP line discipline registered.
SLIP: version 0.8.4-NET3.019-NEWTTY (dynamic channels, max=256).
CSLIP: code copyright 1989 Regents of the University of California.
Partition check:
 hda: hda1
RAMDISK: Compressed image found at block 0
VFS: Mounted root (ext2 filesystem).
pci-scan.c:v1.12 7/30/2003  Donald Becker <becker@scyld.com> http://www.scyld.com/linux/drivers.html
eth0: 3c509 at 0x300 tag 1, 10baseT port, address  00 50 04 04 a8 a3, IRQ 10.
3c509.c:1.16 2/3/98 becker@cesdis.gsfc.nasa.gov
eth1: 3c509 at 0x210 tag 2, 10baseT port, address  00 60 08 9d 9a b5, IRQ 11.
3c509.c:1.16 2/3/98 becker@cesdis.gsfc.nasa.gov
3c59x.c:v0.99Zc 12/15/2003 Donald Becker, becker@scyld.com
  http://www.scyld.com/network/vortex.html
eepro100.c:v1.28a 12/05/2003 Donald Becker <becker@scyld.com>
  http://www.scyld.com/network/eepro100.html
eepro100: No cards found, driver not installed.
rtl8139.c:v1.24 11/13/2003 Donald Becker, becker@scyld.com.
 http://www.scyld.com/network/rtl8139.html
via-rhine.c:v1.16 7/22/2003  Written by Donald Becker <becker@scyld.com>
  http://www.scyld.com/network/via-rhine.html
eth0: Setting Rx mode to 1 addresses.
eth1: Setting Rx mode to 0 addresses.
eth1: Setting Rx mode to 1 addresses.
Kalist Shawxo
Junior Member
 
Posts: 25
Joined: Sun Nov 22, 2009 3:17 am

Re: EXT2 is really slow?

Postby Kalist Shawxo » Sun Nov 29, 2009 10:37 pm

HALLELUJAH!! we have had a breakthrough!

so, after the last msg... I went back into it.. and I checked the BIOS settings again. I had been checking them throughout the whole process.. adjusting cache settings and various .... but had not adjusted them until AFTER installing 4.2 had having problems. the original BIOS settings were the same as 2.7.

anyway, just for the heck of it... I tried what Peter said and just reset the BIOS to "default".. made sure it saw the HDD and then booted into the HD... and no other changes since modifying the lilo config files and here are the boot times:

Started timing at HD access again:
0:36 to start mounting the boot device
1:32 to Modules loading done
1:42 to getting DHCP address
2:45 to getting the login prompt

WOW!

On shutdown, timing from hitting "enter" after typing reboot, it took only 1:08 to shut down.

So Lightning.... here's my question... should I first try resetting the lilo configs back to normal, or put the original kernal back in first?

thanks Peter for the suggestion.... I had not thought it was a BIOS issue cause of no changes being made between versions... but now 4.2 is loading at comparable speeds of 2.7
Kalist Shawxo
Junior Member
 
Posts: 25
Joined: Sun Nov 22, 2009 3:17 am

Re: EXT2 is really slow?

Postby Lightning » Mon Nov 30, 2009 2:45 am

So Lightning.... here's my question... should I first try resetting the lilo configs back to normal, or put the original kernal back in first?

thanks Peter for the suggestion.... I had not thought it was a BIOS issue cause of no changes being made between versions... but now 4.2 is loading at comparable speeds of 2.7

Boot speeds have always been a concern and I have made large effort to impove boot speeds since the first of the 03x series and 04x boots faster than some of the 03x series and not to much slower than 027 with a reasonable processor.

As for the changes I recommend, now that it boots in a normal amount of time I recommend changing things back one thing at a time. The first and biggest improvement will be to put the default kernel back in place so that you can use the CPU math coprocessor rather than a software math coprocessor. You will also need to remove the "no387" from both copies of the lilo.cfg file and you MUST run the "lilo" command after making those changes.
I looked at you dmesg report and it was still loading the 16MB ramdisks so I suspect you did not do that in your previous changes. Also making these changes back one at a time will make it very clear if you still need one or more of them on this machine.
If you are afraid that you might make a mistake. The chances are high that you will never learn anything.
User avatar
Lightning
FREESCO GOD !!
 
Posts: 12080
Joined: Wed Nov 14, 2001 6:50 am
Location: Oregon, USA

Re: EXT2 is really slow?

Postby Kalist Shawxo » Mon Nov 30, 2009 10:08 am

so far, looking good.
I have the no387 removed, running good.
I have the RAMDISK installed, running good.
I have the original kernel installed, running good. last boot was 2:45 to login prompt, and under a minute to shutdown.

so... now that it looks like it was some kind of demonic possession and not a kernel problem. How do I get a kernel suitable for Apache? I looked at the ones for .4.2 and couldn't figure out the best one to grab.
Kalist Shawxo
Junior Member
 
Posts: 25
Joined: Sun Nov 22, 2009 3:17 am

Next

Return to FREESCO Support for v0.4.x

Who is online

Users browsing this forum: No registered users and 10 guests

cron